SYNDUSTRIAL® PAG COMPRESSOR OIL

SYNTHETIC POLYALKYLENE GLYCOL-BASED COMPRESSOR OIL FOR NATURAL GAS SERVICE

Phillips 66® Syndustrial PAG Compressor Oils are premium quality, synthetic lubricants developed for use in reciprocating, oil-flooded rotary screw, centrifugal, and rotary vane compressors processing natural gas, carbon dioxide, propane, or other hydrocarbon gases. They are specially formulated to resist hydrocarbon dilution and oil absorption in this type of service.

You are currently viewing SYNDUSTRIAL® PAG COMPRESSOR OIL

Features & Benefits

  • Highly resistant to dilution by hydrocarbon gases
  • Resists washout by condensed hydrocarbon liquids
  • Resists absorption into the gas stream and subsequent carryover of the lubricant downstream
  • Outstanding oxidation resistance and thermal stability at high temperatures
  • High viscosity index and low pour point for use over a wide temperature range
  • High film strength for wear protection
  • Protects against rust and corrosion
  • Extended service intervals compared with mineral oil-based lubricants
  • Compatible with commonly used seals, gaskets, and hoses(1)

    (1)Note: Syndustrial PAG Compressor Oil is compatible with neoprene, silicone rubber, torlon, vespal and viton, as well as epoxy paints. It is NOT compatible with oil-based paints or with solvents, such as diesel fuel, kerosene, heptane, methanol, ethylene glycol or triethanolamine.

Applications

  • Oil-flooded rotary screw and rotary vane compressors processing natural gas, carbon dioxide, or other hydrocarbon gases
  • Centrifugal compressors processing propane refrigerant, including York centrifugal compressors where York Oil Q (ISO VG 46) or York Oil R (ISO VG 68) is recommended

    Note: Syndustrial PAG Compressor Oil is NOT compatible with petroleum compressor oils. Care should be taken to avoid mixing the two products. When switching over from mineral oil to Syndustrial PAG Compressor Oil, a complete flush, drain, and refill should be performed.

    CAUTION: Syndustrial PAG Compressor Oil is NOT recommended for use in R-134a refrigeration compressors that require a PAG lubricant.

Technical Details

  • ISO Grade: 46
  • Licenses & Approvals

    N/A

    Additional Details

    ISO Grade 46
    Specific Gravity @ 60°F 1.03
    Density, lbs/gal @ 60°F 8.58
    Color, ASTM D1500 0.5
    Flash Point (COC), °C (°F) 263 (505)
    Pour Point, °C (°F) -51 (-60)
    Viscosity
    cSt @ 40°C 46.9
    cSt @ 100°C 9.9
    SUS @ 100°F 236
    SUS @ 210°F 59.6
    Viscosity Index 204
    Acid Number, ASTM D974, mg KOH/g 0.26
    Copper Corrosion, ASTM D130, 48 hrs @ 80°C 1a
    Foam Test, ASTM D892, Seq. I, mL 0/0
    Four-Ball Wear Test, ASTM D4172, Scar Diameter, mm 0.5
    Oxidation Stability, RPVOT, ASTM D2272, minutes 1550
    Rust Test, ASTM D665 A Pass
  • ISO Grade: 68
  • Licenses & Approvals

    N/A

    Additional Details

    ISO Grade 68
    Specific Gravity @ 60°F 1.04
    Density, lbs/gal @ 60°F 8.66
    Color, ASTM D1500 0.5
    Flash Point (COC), °C (°F) 232 (450)
    Pour Point, °C (°F) -39 (-38)
    Viscosity
    cSt @ 40°C 68
    cSt @ 100°C 14.8
    SUS @ 100°F 340
    SUS @ 210°F 78.4
    Viscosity Index 230
    Acid Number, ASTM D974, mg KOH/g 0.34
    Copper Corrosion, ASTM D130, 48 hrs @ 80°C 1a
    Foam Test, ASTM D892, Seq. I, mL 0/0
    Four-Ball Wear Test, ASTM D4172, Scar Diameter, mm 0.47
    Oxidation Stability, RPVOT, ASTM D2272, minutes 2100
    Rust Test, ASTM D665 A Pass
  • ISO Grade: 100
  • Licenses & Approvals

    N/A

    Additional Details

    ISO Grade 100
    Specific Gravity @ 60°F 1.04
    Density, lbs/gal @ 60°F 8.66
    Color, ASTM D1500 0.5
    Flash Point (COC), °C (°F) 232 (450)
    Pour Point, °C (°F) -36 (-33)
    Viscosity
    cSt @ 40°C 100
    cSt @ 100°C 19.4
    SUS @ 100°F 503
    SUS @ 210°F 97.8
    Viscosity Index 218
    Acid Number, ASTM D974, mg KOH/g 0.34
    Copper Corrosion, ASTM D130, 48 hrs @ 80°C 1a
    Foam Test, ASTM D892, Seq. I, mL 0/0
    Four-Ball Wear Test, ASTM D4172, Scar Diameter, mm 0.51
    Oxidation Stability, RPVOT, ASTM D2272, minutes 2100
    Rust Test, ASTM D665 A Pass
  • ISO Grade: 150
  • Licenses & Approvals

    N/A

    Additional Details

    ISO Grade 150
    Specific Gravity @ 60°F 1.05
    Density, lbs/gal @ 60°F 8.75
    Color, ASTM D1500 0.5
    Flash Point (COC), °C (°F) 263 (505)
    Pour Point, °C (°F) -49 (-56)
    Viscosity
    cSt @ 40°C 150
    cSt @ 100°C 27.8
    SUS @ 100°F 682.5
    SUS @ 210°F 135.6
    Viscosity Index 227
    Acid Number, ASTM D974, mg KOH/g 0.34
    Copper Corrosion, ASTM D130, 48 hrs @ 80°C 1a
    Foam Test, ASTM D892, Seq. I, mL 0/0
    Four-Ball Wear Test, ASTM D4172, Scar Diameter, mm 0.3
    Oxidation Stability, RPVOT, ASTM D2272, minutes 1500
    Rust Test, ASTM D665 A Pass
Search this website Type then hit enter to search